SELF TAPPING THREADED INSERT W. THREE CUTTING HOLE

SELF TAPPING THREADED INSERT
W. THREE CUTTING HOLE

MATERIAL AVAILABLE: 
STEEL, STAINLESS STEEL, ALUMINUM, ALUMINUM ALLOY, BRASS

FOR USE IN THICK WALL OR CLOSE TO AN EDGE

ADVANTAGE:
1.HIGH PULL-OUT STRENGTH
2.HIGH TORQUE RESISTANCE
3.STRONG WEAR RESSTANCE THREAD
4.FAST, EASY INSTALLATION
5.EXTREME VIBRATION RESISTANCE

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

THICK WALL SECTION
SELF TAPPING THREAD INSERTS W. THREE CUTTING HOLE - THICK WALL SECTION

 

BINDING POST

BINDING POST
CHICAGO SCREW

MATERIAL AVALIABLE: 
ALUMINUM, BRASS, STAINLESSSTEEL

SURFACE FINISH AVALIABLE: 
CLEAN

GREAT CHOICE FOR SWATCH BOOKS, ARCHITECTURAL AND ENGINEERING DRAWINGS, OR ANY APPLICATION WHERE LOOSE SHEETS NEED TO BE KEPT TOGETHER.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

   

 

SELF TAPPING THREADED INSERT MANUAL INSTALLATION TOOLS

SELF TAPPING THREADED INSERT
MANUAL INSTALLATION TOOLS

I. HOLE SIZE: 
RECOMMENDED HOLE SIZE IS INDICATED ON EACH DATA SHEET AND IS INTENDED TO BE FOR REFERENCE ONLY. HOLE SIZE MAY NEED TO BE INCREASED OR DECREASED DEPENDING ON BASE MATERIAL, INSTALLATION TORQUE OR PERFORMANCE REQUIRED. OPTIMUM HOLE SIZE SHOULD BE DETERMINED BY REQUESTING SAMPLES & INSTALLING THEM IN THE INTENDED MATERIAL.

II. HOLE DEPTH: 
IN THRU HOLE APPLICATIONS THE INSERT LENGTH SHOULD NOT EXCEED THE MATERIAL THICKNESS. IN BLIND HOLE APPLICATIONS THE HOLE DEPTH SHOULD BE 1.2XINSERT LENGTH AND THIS VALUE IS INDICATED ON MOST DATA SHEETS.

III. COUNTERSINK 
A 60°COUNTERSINK IS REQUIRED FOR MOST MATERIALS TO INSURE A FLUSH SURFACE AFTER INSTALLATION.

IV. WALL THICKNESS 
WALL THICKNESS SHOULD BE 0.35 TO 0.5 X HOLE DIAMETER DEPENDING ON BASE MATERIAL.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

 

   

E SELF-DRIVING NUT

E SELF-DRIVING NUT
MATERIAL AVALIABLE: 
STEEL, STAINLESS STEEL AND BRASS

ADVANTAGES:
1.INSTALL SLEEVE NUT TO ACCESS FRONT SIDE OF THE WORK PIECE & SCREW IN FROM BACK SIDE.
2.INSTALL WITHOUT ANY COMPLICATED TOOL AT ANY LOCATION ON THE ASSEMBLY.
3.INSTALL WITHOUT PRODUCING ANY HARMFUL MARK.
4.INSTALL INTO VARIES MATERIAL.
5.THE FANGS ON THE BODY CUT INTO THE APPLICATION DURING ASSEMBLY.
6.EASY, FAST & SAFE INSTALLATION.

INSTRUCTIONS OF E-SELF DRIVING NUT:
AS THE SLEEVE NUT IS STALLED, THE FANGS ON THE BODY ACTUALLY CUT INTO THE APPLICATION & PROVIDES GRIP STRENGTH. WHEN SCREW ON THE OPPOSITE SIDE HAVE DRIVEN, THE FANGS WILL GRIP APPLICATION TIGHTLY.

FEATURE OF E-SELF DRIVING NUT
(COMPARE WITH SEX BOLTS) 

I. ROUND BODY WITH FANGSON IT 
1.GRIP THE APPLICATION TIGHTLY
2.CANNOT BE DISASSEMBLED EASILY
3.PREVENT ANY ONE WHO INTENT TO PULL OUT

II. SCREW HEADCAN BE YOUR CHOICE 
1.THE SCREW HEAD CAN BE TAMPERPROOF
2.HARDLY TO DISASSEMBLED
3.COMBINE WITH GOOD SURFACE OUTLOOK

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST 

 

 

 

SPEED PIN RIVET DRIVE PIN RIVET

SPEED PIN RIVET / DRIVE PIN RIVET

MATERIAL AVAILABLE FOR SPEED PIN RIVET (DRIVE PIN RIVET): 
BODY: ALUMINUM 2117 / STAINLESS STEEL 302 (INOX A2/18-8) / STEEL 1006
PIN: ALUMINUM 2024 / STAINLESS STEEL 304 (INOX A2/18-8) / STEEL 1022

FINISH SURFACE AVAILABLE FOR SPEED PIN RIVET (DRIVE PIN RIVET): 
PLATING: CR3 WHITE ZINC PLATED/ CR3 YELLOW ZINC PLATED/ CR3 BLACK ZINC PLATED/ ANODIZED/CLEAN

ADVANTAGES OF SPEED PIN RIVET (DRIVE PIN RIVET): 
1.SPEED PIN RIVET IS FAST AND EASY TO INSTALL.
2.NO SPECIAL INSTALLATION TOOL IS REQUIRED FOR SPEED PIN RIVET, JUST A HAMMER WILL DO.
3.VARIOUS MATERIALS ARE AVAILABLE FOR SPEED PIN RIVET.
4.VARIOUS HEAD STYLES ARE AVAILABLE FOR SPEED PIN RIVET.
5.SPEED PIN RIVET WILL NOT DAMAGE THE APPLICATION SURFACE
6.SPEED PIN RIVET CAN BE RUST RESISTANT.
7.SPEED PIN RIVET CAN BE APPLIED TO WIDE THICKNESS.
8.THE APPEARANCE LOOKS GOOD AFTER INSTALLATION.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
★Available Size:5/32"、5/16"、3/16"、3/8"、1/8"、1/4"、

MALE FEMALE RIVET

MALE FEMALE RIVET

MATERIAL: ALUMINUM 5052 BRASS 2600 STAINLESS STEEL 302 / 410

APPLICATION : TABLEWARE

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

  

REBITADOR MANUAL

REBITADOR MANUAL

 

WEIGHT：0.6kg (1.32lb)
RIVET SIZE：2.4mm(3/32"),3.2mm(1/8"),4.0mm(5/32"),4.8mm(3/16").

RIVET MATERIAL：ALUMINUM & BRASS

RIVET FETURE：
1.INSTALL WITHOUT PRODUCING ANY HARMFUL MARK.
2.EASY, FAST & SAFE INSTALLATION.

SQUARE BLIND JACK NUT

SQUARE BLIND JACK NUT

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST 

1.The Square Blind Jack Nut is an economical blind fastener designed for assembly lind use in THIN, SOFT or BRITTLE materials.
2.When tightened, their body collapses to form legs which grip the inside of the mounting surface, leaving a permanent reusable threaded insert.
3.Standard blind jack nut are manufactured of steel with a commercial zinc plating.
4.All blind jack nuts can be supplied with brass coated which assist galvanic corrosion concerns.

MATERIAL AVAILABLE : STEEL, STAINLESS STEEL304, BRASS

FEATURES： 
1.FASTENS IN BLIND HOLES
2.FASTENS SECURELY DESPITE BURRS & UNEVEN SUBSTRATES
3.NOT HOLE SIZE SENSITIVE
4.SUITABLE FOR WIDE GRIP RANGE

ALUMINUM & STEEL BLIND RIVET TS.AAS. SERIES

ALUMINUM / STEEL BLIND RIVET
TS.AAS. SERIES

 

MATERIAL AVALIABLE: 
RIVET: ALUMINUM 5050
SHAFT: STEEL 1018~1022

FINISH SURFACE AVALIABLE: 
RIVET: SELF COULOUR/ COLOURED IN YELLOW/ BLACK/ WHITE/ RED...ETC
SHAFT: CR3 WHITE ZINC PLATED/ CR3 YELLOW ZINC PLATED

ADVANTAGES OF AL-ST BLIND RIVET: 
1.PROVIDE STRONG HOLDING FOR APPLICATION.
2.LOW IN COST COMPARE WITH BOLT AND NUT.
3.IDEAL FOR WIDE RANGE APPLICATION.
4.AVAILABLE IN DOME, COUNTERSUNK OR LARGE FLANGE STYLE.
5.FAST AND EASY TO INSTALL.
6.IDEAL FOR RUST RESISTANCE APPLICATION.
7.IDEAL FOR LIGHT WEIGHT USAGE.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

HIGH SHEAR STRENGTH BLIND RIVET

HIGHT SHEAR STRENGTH BLIND RIVET

 

 

 

MATERIAL AVALIABLE: 
RIVET: STEEL
SHAFT: STEEL

ADVANTAGES OF HIGH SHEAR STRENGTH BLIND RIVER: 
1.EASY & FAST INSTALLATION
2.HIGH FASTENING STRENGTH
3.THE MANDREL WILL BE CUT OFF OUTSIDE OF BODY AFTER RIVETING FOR INCREASING THE SHEAR STRENGTH
4.THE SHEAR STRENGTH IS ALMOST TWICE THAN THE ORIGINAL RIVET
5.SUITABLE FOR CONTAINER, BODY WORK, ELECTRIC CABINET, AND CONCTRUCTION ETC.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST 
ALL STEEL BLIND RIVET V.S. HIGH SHEAR STRENGTH BLIND RIVER
HEAD

SIDE

INSPECTION REPORT OF SHEAR STRESS

 

STRETCH FOLDING BLIND RIVET ( TRI FOLD BLIND RIVET )

STRETCH FOLDING BLIND RIVET
( TRI FOLD BLIND RIVET )

MATERIAL AVALIABLE: 
RIVET: ALUMINUM 5050
MANDREL: ALUMINUM 5056

POSITIVE: RATTLE FREE FASTENER

CORROSION RESISTANT: 
ALL ALUMINUM CONSTRUCTION

MULTIGRIP: 
ADJUSTS TO A WIDE VARIATION OF SUBJECT'S THICKNESS.
FINISH AVAILABLE IN A MULTIPLE COLOR.

SUITABLE APPLICATIONS: 
SUPPORTS BRTTLE THIN SOFT OR DUCTILE MATERIALS & FUNCTIONS WHEN USED WITH OVERSIZED, ISALIGNED OR IRREGULARLY SHAPED HOLES.
THE STRETCH FOLDING BLIND RIVET FORMS THREE LARGE FOLDING LEGS THAT CREATE EXCELLENT CLAMPOING-UP & A LARGE BLIND SIDE BEARING SURFACE.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST